How Auto Transmission Stocked in D After a Minute of Driving

How Auto Transmission Stocked in D After a Minute of Driving.

 

How Auto Transmission Stocked in D After a Minute of Driving

 

Model: Hyundai Sonata YF

Year of Model: 2011

Fuel: Gasoline

Displacement: 2400 cc

 

1) Study Guide the Condition.

1. Auto Transmission Stocked after a minute of driving.

2) Study Guide the Cause

1. Brake Switch.

3) Study Guide and Diagnosis

1. Scan Tool Checked
   = No Trouble Found.
2. Confirm the Problem by testing the car = the problem was occurs
3. Lift the car on 2 post electric lifter the test to put the shifting lever to drive and let the wheel run then push the brake pedal to stop and try to return the shifting lever to park position but it can not.
4. Check the Current flowing to the shifting solenoid from brake switch. No Power flowing.

4) Study Guide and Replace Parts

1. Brake Switch.

more and more trouble shooting about manual and automatic transmission

How to Repair Abnormal Tachometer.

How to Repair Abnormal Tachometer.

 

How to Repair Abnormal Tachometer

Model: Hyundai Trajet (FO)

Model Year: 2002

Fuel : Diesel

Displacement: 2000cc

 

1) Study Guide and Condition

1. Study When engine Starts, the cranking is impossible and the tachometer fails to operates.

2) Study Guide and Trouble Cause

1. Abnormal Tachometer

3)Study Guide and Trouble Diagnosis

1. The G-Scan shows normal engine RPM.
2. The Main wiring MC21 connector #12  terminal (0.3 W) is normal.
3. Test between the MC21 connector #12 terminal and the M30-2 connector #12 terminal continuously – Normal
4. Check the Tachometer B+ power source.
5. Check the tachometer on the instrument cluster.
6. Tachometer is abnormal.

4) Study Guide and Repair Guide

1. Replace the Instrument Cluster Assembly.

Study Guide and Auto Repair and Repair Guide

How to Repair Sonata YF Shift Locked During Driving

How to Repair Sonata YF Shift Locked During Driving

 

How to Repair Sonata YF Shift Locked During Driving

 

Study Guide and Condition

1. Study Why Hyundai Sonata YF Locked on Drive position After Driving.
2. Study What is the cause of Locked on Drive position to Reverse.

Study Guide and Cause

1. This trouble usually cause of the Shifting lever solenoid.

Study Guide and Diagnosis

1. Scan Tool Checked
   =No Trouble Found
2. Check the Brake Switch For Function = OK normally function.
3. Remove the console box to checked the power of solenoid = Ok.
4. Visually check the solenoid for function = Fail sometime the solenoid nor working.
5. Replace with new and good parts ok ITS WORKING NORMALY.

Study Guide and Replace parts

1. Replace Shift Solenoid Switch.

Study Guide and Replace Parts

How to Repair illumination Light On & Off

How to Repair illumination Light On & Off

 

How to Repair illumination Light On & Off

Model: Hyundai Azera TG

Year Model: 2011

Fuel : Gasoline

Displacement: 2700cc

 

A) Study Guide and Condition:

1. Study A/C Illumination light.
2. Study Audio Radio illumination light.
3. Study Glove Box illumination light.
4. Study Tray illumination light
   = Lights on and off while applying brake.
5. Study Audio Radio illumination immediately light on  When the ignition key is in On position supposed to be light off.

B) Study Guide and Cause

1. Due to LED Bulb put in the plate light as a replacement of the original bulb.

C) Diagnosis and Study Guide

1. Scan tool Check
   = no trouble code
2. Study and Check the illumination diagram.
3. Study and Check the power and the Ground terminal.The power terminal wire color is brown/black.For the Ground terminal is black wire color.

(Note all illumination light On only when the multifunction switch or Head light switch is in park light on)

1. Study The Brown/Black which is power has a Continues Power volt 2.3 volt = Abnormal.
2. Study Disconnect all part has a illumination light one by one.
3. Study Disconnect the tail light then  test by pushing the brake pedal the illumination light return to normal.
4. Study Check all lighting system at the back = The plate light has mounted a LED bulb by the owner. pull out then all lighting system return to normal function.

D) Study Guide and Auto Repair

1. Replace Plate bulb.
2. more trouble and General description

How to Check P0340 CMP of Hyundai Sonata EF

How to Check P0340 CMP of Hyundai Sonata EF

How to Check P0340 CMP of Hyundai Sonata EF

Study Guide and General Description

2002  2.0 DOHC Engine  P0340 Camshaft Position Sensor Circuit Malfunction

Study Guide Component Location Study Guide Description 1. General Description Study Guide The Camshaft Position Sensor (CMPS) is a sensor that detects the compression TDC of the NO. 1 cylinder. The CMPS consists of a hall type sensor and a target on the end of the intake camshaft. When the target triggers the sensor, the sensor voltage is 5V. If not, the sensor voltage is 0V. These CMPS signal is sent to the ECM and the ECM uses the CMPS signal for synchronizing the firing of sequential fuel injectors.

2002   2.0 DOHC  Engine  Unleaded GEN(Siemens)  P0340 Camshaft Position Sensor Circuit Malfunction

Study Guide Terminal and Connector Inspection 1. Study Guide Many malfunctions in the electrical system are caused by poor harness(s) and terminals. Faults can also be caused by interference from other electrical systems, and mechanical or chemical damage. 2. Study Guide Check the following conditions: (1) Study Check for damaged harness and terminals: contact resistance, oxidation, bent or broken terminals. (2) Study Check for poor connection between ECM and component: backed out terminal, improper mating, broken locks or poor terminal to wire connection Use a suitable male pin to ensure that contact in sockets is good. The pin should remain in position when pulled gently. 3. Study Has a problem been found? YES 1) Study Repair as necessary and go to "Verification of Vehicle Repair" procedure NO 1) Study Go to "Power Circuit Inspection" procedure. Power Supply Circuit Inspection Check Power to CMPS 1. Study IG KEY : OFF , Engine : OFF 2. Study Disconnect CMPS connectorC05. 3. Study IG KEY : ON , Engine : OFF 4. Study Measure voltage between terminal 3 of the CMPS harness connectorC05 and chassis ground. A. [Specification] Approx.B+ 5. Study Guide Is the voltage near the specified value? YES 1) Study Guide Go to "Ground Circuit Inspection" procedure. NO 1) Study Guide Repair open or short to ground in harness, Go to "Verification of Vehicle Repair" procedure. Study Guide Ground Circuit inspection Check for Open in Harness 1. Study Guide IG KEY : OFF , Engine : OFF 2. Study Guide Disconnect CMPS connectorC05 and ECM connector. 3. Study Guide Measure resistance between terminal 1 of the CMPS harness connectorC05 and chassis ground. A. [Specification] Approx.0Ω 4. Study Guide Is the resistance near the specified value? YES 1) Study Guide Go to "Signal Circuit Inspection" procedure. NO 1) Study Guide Repair open in harness, Go to "Verification of Vehicle Repair" procedure. Study Guide Signal Circuit Inspection Check for Open in Harness 1. Study Guide IG KEY : OFF , Engine : OFF 2. Study Guide Disconnect CMPS connectorC05 and ECM connector. 3. Study Guide Measure resistance between terminal 2 of the CMPS harness Study Guide connectorC05 and 16 of the ECM harness connectorC44-2. A. [Specification] Approx.0Ω 4. Study Guide Is the resistance near the specified value? YES 1) Study Guide Go to "Check for Short to Ground in Harness" NO 1) Study Guide Repair open in harness, Go to "Verification of Vehicle Repair" procedure. Check for Short to Ground in Harness 1. Study Guide IG KEY : OFF , Engine : OFF 2. Study Guide Disconnect CMPS connectorC05 3. Study Guide Measure resistance between terminal 2 of the CMPS harness connectorC05 and chassis ground. A. [Specification] infinite(∞Ω) 4. Study Guide Does the resistance indicate open? YES 1) Study Guide Go to "Check for Short to Battery in Harness" NO 1) Study Guide Repair short to chassis ground in harness, Go to "Verification of Vehicle Repair" procedure. Check for Short to Battery in Harness 1. Study Guide IG KEY : OFF , Engine : OFF 2. Study Guide Disconnect CMPS connectorC05. 3. Study Guide IG KEY : ON , Engine : OFF 4.   5.   . more info Study Guide and Auto Repair and Study Guide and Auto Repair

How to Repair Sometimes Coupe not Crank

How to Repair Sometimes Coupe not Start

Model: Hyundai Coupe BK

Year Model: 2010

Fuel: Gasoline

Displacement: 3800cc

How to Repair Sometimes Coupe not Start

Study Condition:

1. Intermittent engine not cracking after an hour of parking.
2. Sometimes only the pre start will function for engine start.

Study Cause:

1. Due to PDM ( Power Distribution Module) intermittent malfunctioning.

Study Diagnosis :

1. Study Scan tool check
   =  The trouble was regarding on immobilizer.
2. Study Confirm the problem start the engine to test until the problem appear(OK confirm) but still the trouble for the second time will not registered and can not show to the GDS( Diagnostic Trouble System).
3. Study Now the was confirm and the engine will not start.
   = Check for the power from the starter relay. Fail No power.
   = At the same time no trouble code, Check for the power of Button Start and Smart Key System from the fuse to button switch OK.
   = Check the power supply from Button Start and Smart Key System to the PDM.OK
   = Check the PDM power to the main relay for starting system. Fail No power.

Study Guide and Replace parts

1. Replace PDM assembly.
2. more and more case for  you  to have a tips on Hyundai   trouble shooting

Study Guide , Auto Repair , Study Guide , Auto Repair , Study Guide , Auto Repair

How to Check 2010 1.6 DOHC Hyundai Elantra

P0712 Transaxle Fluid Temperature Sensor Circuit Low Circuit

Study Guide Component Inspection Check "TRANSAXLE FLUID TEMPERATURE SENSOR" 1. Study Ignition "OFF" . 2. Study Disconnect the "TRANSAXLE FLUID TEMPERATURE SENSOR" connector 3. Study Measure the resistance between terminals "5" and "6" of the "TRANSAXLE FLUID TEMPERATURE SENSOR". A. Study the Specification : Refer to " Reference data" TEMP.(°C) RESISTANCE(kΩ) TEMP.(°C) RESISTANCE(kΩ) -40(-40°F) 139.5 80(176°F) 1.08 -20(-4°F) 47.7 100(212°F) 0.63 0(32°F) 18.6 120(248°F) 0.38 20(68°F) 8.1 140(284°F) 0.25 40(104°F) 3.8 160(320°F) 0.16 60(140°F) 1.98 Study , Study , Study , Study , Study , Study , Study , Study , Study 4. Study Is resistance within specifications or w/in Study? YES 1) Go to "CHECK PCM/TCM " as below NO 1) Study Guide Replace "TRANSAXLE FLUID TEMPERATURE SENSOR" as necessary and Go to "Verification Vehicle Repair"Study procedure. Study Guide , Study Guide , Study Guide , Study Guide , Study Guide Check TCM 1. Study Ignition "ON" & Engine "OFF". 2. Study Connect "TRANSAXLE FLUID TEMPERATURE SENSOR" connector. 3. Study Install scantool and slect a SIMU-SCAN, 4. Study Simulate voltage (0→5V) to "TRANSMISSION FLUID TEMPERATURE SENSOR" signal circuit. 5. Study Is FLUID TEMP. SENSOR signal value changed according to simulation voltage? YES 1) Study Thoroughly check connectors for looseness, poor connection, bending, corrosion, contamination, deterioration, or damage. Repair or replace as necessary and then go to "Verification of Vehicle Repair" procedure. NO 1) Study Substitute with a known-good PCM/TCM and check for proper operation. If the problem is corrected, replace PCM/TCM as necessary and go to "Verification of Vehicle Repair" procedure. Study Guide and Auto Repair and Study Guide and Auto Repair and Study   more Study Guide and Auto Repair

How Hyundai EQUUS Code P0017 Works?

P0017 Crankshaft Position – Camshaft Position Correlation (Bank 1 Sensor B)

Study Guide

Auto Repair

Component Location w/ Auto Repair and Study Guide Auto Repair and Study Guide General Description Auto Repair A Crankshaft Position Sensor (CKPS) is a magnetic type sensor that generates voltage using a sensor and a target wheel mounted on the crankshaft.Study Guide The PCM calculates engine RPM by using the sensor’s signal and controls the injection duration and the ignition timing. Camshaft Position Sensor (CMPS) is a hall sensor and detects the camshaft position by using a hall element. It is related to Study with Crankshaft Position Sensor (CKPS) and detects the piston position of the each cylinder which the CKPS can’t detect. This CMPS signal is sent to the PCM and it uses CMPS signals for determining the ignition timing with CKPS signals. CMPS makes Sequential Injection possible. Auto Repair w/ DTC Description If the deviation between CKPS and CMPS(EX-CMPS Bank 1) is bigger than the threshold value, ECM sets DTC P0017. Study Guide w/ DTC Detecting Condition Item Detecting Condition Possible Cause Case1 Study Guide DTC Strategy • Camshaft install diagnosis • Poor connection • Contamination of Oil / Clog of Oil path • CKPS, CMPS • OCV • CVVT Enable Conditions Study Guide • First firing detected after ECM installed or ‘Camshaft install fault exist • Adapted CMP - CMP < 2 Deg Threshold Value Study Guide • | Adapted CMP – Set value |> 7 Deg Case2 Study Guide DTC Strategy • Camshaft and crankshaft alignment check Enable Conditions Study Guide • Adapted CMP - CMP < 2 Deg • Engine speed < 1500rpm • Engine load < 50% • ECT > 60C Threshold Value Study Guide • | Adapted CMP – Set value – Adaped CMP during install diagnosis | > 13 Deg Diagnostic Time Study Guide • 6 camshaft rotations MIL On Condition Study Guide • 2 driving cycle More Study Guide and Auto Repair for the engine and transmission

How to Repair Engine RPM up and Down

How to Repair Engine RPM up and Down

Model: Hyundai Sonata

Year Model: 2002

Displacement: 2000cc

Condition:

1. Engine RPM up and Down.
2. Engine Cut Off Especially when Getting Engine Hot.

Cause:

1. Due to CKP sensor wire open.
   = CKP wire covered only with Electrical tape and this the cause of resistance that affect the CKP sensor.

Diagnosis

1. Scan tool Check
   =Study P0010 CMP Sensor.
2. Check the Electrical circuit of CMP
   =Study OK
3. Check the Fuel Pressure
   = Study OK.
4. Check  The CPK by disconnecting the female &male Socket.
5. Check the electrical circuit for loose connection =Study
6. Check for the engine timing cause CMP trouble code intermittently registered to the GDS or G-Scan.Study Ok
7. Finally Open the Front Engine and check visually the CKP
   =Study CKP wire covered only with Electrical tape and this the cause of resistance that affect the CKP sensor.

Study Guide and Replace Parts

1. Replace Crankshaft Position Sensor. 

Study Guide , Study Guide , Study Guide , Study Guide , Study Guide

How to repair A/T overdrive not working

How to repair A/T overdrive not working of Hyundai Trajet

Model: Hyundai Trajet

Year Model: 2004

Displacement:2700cc

Fuel: Gasoline

1) Study Condition

1. Automatic Transmission Overdrive switch not working

2) Study the Cause

1. This problem cause of electrical circuit from overdrive switch disconnected.

3) Study and Diagnosis

1. Study and Check with GDS
   = No Trouble Found
2. Study and Check fuse from overdrive circuit = OK
3. Study and Open the Steering column were the shifting lever mounted.
4. Study and Check for the wire of overdrive switch and disconnet.
5. Study and Check the B+
   = no current flows
   = Check for the socket pin, the problem found from the socket only the cover of wire connected to the socket.

4) Study Guide and Repair Procedure

• Repair The disconnected parts

more training and trouble shooting

Study , Study , Study , Study , Study , Study , Study , Study , Study , Study.

How to check output speed sensor code P0722

How to check output speed sensor code P0722

 

P0722 A/T Output speed Sensor Circuit - Open or Short(GND)

Study Guide

Auto Repair

Study Guide and Component Location Study Guide and General Description Study Guide and The Output Speed Sensor outputs pulse-signals according to the revolutions of the output shaft of the transmission. Study Guide and  The Output Speed Sensor is installed in front of the Transfer Drive Gear to determine the Transfer Drive Gear rpms by counting the frequency of the pulses.Study This value, together with the throttle position data, is mainly used to decide the optimum gear position. Study Guide and DTC Description Study The TCM sets this code if the calculated value of the pulse-signal is noticeably different from the value calculated, using the Vehicle Speed Sensor output, when Study the vehicle is running faster than 30 km/h. The TCM will initiate the fail safe function if this code is detected. Study Guide and DTC Detecting Condition Item to Study Detecting Condition and Study Study Possible Cause DTC Strategy ● Speed rationality check ● Signal circuit is open or short. ● Sensor power circuit is open ● Sensor ground circuit is open ● Faulty OUPUT SPEED SENSOR ● Faulty PCM Enable Conditions ● Battery Voltage ≥ 10V ● Lever position : D,3,2,L ● State of brake : OFF Threshold Value ● Output speed = 0 Diagnostic Time ● More than 1sec Fail Safe ● Locked into 3rd or 2nd gear. ● Manual shifting is possibe(2 nd → 3 rd ,3 rd → 2 nd) more cases and  information Study and Study and Study and Study and Study and Study and Study and Study

How input sensor works? code P0717

How input sensor works?code P0717

Model: Hyundai Elantra

Year Model: 2010

Fuel: Gasoline

Displacement: 1600cc

 

Transmission  Automatic Transaxle  P0717 A/T Input speed Sensor Circuit Low Input

Study Guide and Component Location Study Guide and General Description The Study Guide input(turbine) speed sensor outputs waveform signals according to the revolutions of the input shaft ,installed in front of End clutch retainer,of the transmission. The Study Guide TCM determines the input shaft speed by calculating the frequency of the pulses. This Study Guide value is mainly used to control the optimum fluid pressure during shifting. Study Guide and DTC Description The Study Guide PCM/TCM sets this code if an output pulse-signal is not detected, from the input speed sensor, when the vehicle is running faster than 30 km/h. The Study Guide Fail-Safe function will be set by the PCM/TCM if this code is detected. DTC Detecting Condition Item Study Guide Detecting Condition Study Guide Possible Cause Study Guide Study Guide and DTC Strategy ● Speed rationality check ● Signal circuit is open or short. ● Sensor power circuit is open ● Sensor ground circuit is open ● Faulty INPUT SPEED SENSOR ● Faulty PCM/TCM Study Guide Enable Conditions ● Battery Voltage ≥ 10V ● Output speed ≥ 1000rpm ● Engine speed(Only current gear is the 1st gear) ≥ 3000rpm ● Lever position : D,3,2,L Study Guide and Threshold Value ● Input speed = 0 Study Guide and Diagnostic Time ● More than 1sec Fail Safe ● Locked into 3rd or 2nd gear. ● Manual shifting is possibe(2 nd → 3 rd ,3 rd → 2 nd) Study Guide and Specification Input shaft & Output shaft speed sensor ● Type : Hall sensor ● Current consumption : 22mA(MAX) ● sensor body and sensor connector have been unified as one. Study Guide and Schematic Diagram Study Guide and Signal Waveform

more case and study guide

How to Repair Engine Vibration in Hyundai Sonata

How to Repair Engine Vibration in Hyundai Sonata

Some Trouble may Cause of Poor Contact of Harness, Sensor Fault, or Mechanical part that affect the normal function of Engine.

Model: Hyundai Sonata YF

Year: 2011

Displacement: 2400cc

1) Study Guide Condition:

• Engine Vibration on Idling.
• Front Engine Noise During Driving.

2) Auto Repair Cause:

1. Due to A/C compressor Internal Damage and Hard to Turn.

   

3) Study Guide Diagnosis

1. Check w/ Scan Tool = No Trouble Code
2. Check Fuel Pressure = Ok
3. Check for the Injector = OK
4. Check For the Spark plug= OK
5. Check  and turn manually the Engine to check if smoothly rotate but pull out the Spark plug.
   = Hard to turn
   = Pull out the Outside Belt then turn = OK
   = Check the all tensioneer bearing and A/C compressor
   = Found Out that the Compressor slightly stuck up

4) Auto Repair and Replace Part

1. Replace w/ new A/C compressor.

more case and Study Guide at the same time Auto Repair Procedure

Auto Repair , Study Guide , Auto Repair , Study Guide , Auto Repair , Study Guide 

How to Repair Engine Cut Off When Shift to ‘R’ and ‘D’ Position

How to Repair Engine Cut Off When Shift to ‘R’ and ‘D’ Position

This Case may Give You Some Idea or tips so that you can analyze what ‘s going on to your Hyundai car.This Trouble actual trouble shooting that I solution.

Model: Elantra HD

Year Model: 2010

Fuel : Gasoline

Displacement: 1600cc

1) Condition

1. Engine Cut Off When Shift to ‘R’ and ‘D’ posotion

2) Cause

1. A/T valve Body

3)Diagnosis

1. Check with GDS for Trouble Code
   = Code = P0742 – Torque Converter Clutch Circuit stuck On.
2. Check for the electrical circuit = Ok
3. The possible cause of this Code valve Body and ECU
4. Fist Replace with known good ECU = The same The Problem Occurs
5. Pull the Valve And Replace with new valve Body.
6. Re-fixed all parts then Check= the Problem suddenly disappeared.

4)Replace Parts

• Assembly Valve Body.
• More Case Study and trouble code Description

Auto Repair , Study Guide , Auto Repair , Study Guide , Auto Repair , Study Guide

How to Check Code P0743 of Hyundai

How to Check Code P0743 of Hyundai

Sonata FL 2009  G 2.4 DOHC  Transmission  Automatic Transaxle(A5GF1)  P0743 Torque Converter Clutch Circuit Electrical

AUTO REPAIR AND Component Location STUDY GUIDE AND General Description The PCM/PCM/TCM controls the locking and unlocking of the Torque Converter Clutch ( or Damper Clutch ), to the input shaft of the transmission, by appling hydraulic pressure. The main purpose of T/C clutch control is to save fuel by decreasing the hydraulic load inside the T/C. The PCM/PCM/TCM outputs duty pulses to control the Damper Clutch Control Solenoid Valve( DCCSV ) and hydraulic pressure is applied to the DC according to the DCC duty ratio value. When the duty ratio is high, high pressure is applied and the Damper Clutch is locked. The normal operating range of the Damper Clutch Control duty ratio value is from 30%(unlocked) to 85%(locked). STUDY GUIDE AND DTC Description The PCM/PCM/TCM checks the Damper Clutch Control Signal by monitoring the feedback signal from the solenoid valve drive circuit. If an unexpected signal is monitored (for example, high voltage is detected when low voltage is expected, or low voltage is detected when high voltage is expected) the PCM/PCM/TCM judges that DCCSV circuit is malfunctioning and sets this code. STUDY GUIDE AND DTC Detecting Condition Item Detecting Condition Possible Cause DTC Strategy • Check voltage range ※ TORQUE CONV________? • Open ____________? • _________________? • _____________? Enable Conditions • 16V  Voltage Battery 10V • In gear state(no gear shifting) 0.5sec is passed from turn on the relay Threshold Value • Feedback voltage from DCC control solenoide vb-2V and DCC control duty is 100% • Feedback voltage from DCC control solenoide 5.5V and DCC control duty is 0% Diagnostic Time • ------------ Fail Safe •   STUDY GUIDE AND Specification -   -   -   - Internal resistance : 2.7~3.4Ω(68°F or 20°C) - Surge voltage : 56 V STUDY GUIDE , AUTO REOAIR , STUDY GUIDE , AUTO REPAIR , STUDY GUIDE , AUTO REPAIR STUDY GUIDE , AUTO REPAIR , STUDY GUIDE , AUTO REPAIR , STUDY GUIDE , AUTO REPAIR MORE INFORMATION AND TROUBLE STUDY

How to Replace Spark Plug of Azera

How to Replace Spark plug of Azera

Model: Hyundai Azera (TG),ViraCruz , Genesis BH , Sonata

Year Model: 2010

Fuel : Gasoline

Displacement:3300 cc and 3800cc

 

2009  G 3.3 DOHC  Engine Electrical System

Auto Repair and Study Guide  to Removal IGNITION COIL 1. Remove the engine cover. 2. Disconnect the ignition coil connector(A). Auto Repair Notice   When removing the ignition coil connector, pull the lock pin(A) and push the clip(B). 3. Remove the ignition coil (B). 4. Installation is the reverse of removal. ON-VEHICLE INSPECTION SPARK TEST 1. Remove the ignition coil connector(A). Auto Repair and Study Guide to Notice   When removing the ignition coil connector, pull the lock pin (A) and push the clip(B). 2. Remove the ignition coil(B). 3. Using a spark plug socket, remove the spark plug. 4. Install the spark plug to the ignition coil. 5. Ground the spark plug to the engine. 6. Check if spark occurs while engine is being cranked. Notice for Auto Repair and Study Guide   To prevent fuel being injected from injectors while the engine is being cranked, remove the fuel pump relay(A) from the fuse box. Crank the engine for no more than 5 ~ 10 seconds. 7. Inspect all the spark plugs. 8. Using a spark plug socket, install the spark plug. 9. Install the ignition coil. 10. Reconnect the ignition coil connector.   1.   Study Guide , Study Guide , Study Guide , Study Guide , Study Guide , Study Guide , For more study  and Guide

How to Check The Shock Shifting of Hyundai=Poor Contact

How to Check the Shock Shifting of Hyundai=Poor Contact

How to Check The Shock Shifting of Hyundai=Poor Contact

Model: Hyundai Elantra(HD)

Year Model: 2010

Fuel: Gasoline

Displacement: 1600cc

1) Auto Repair and Study Guide Condition

1. Automatic Transmission Shock Shifting from N to D
2. Speedo meter Fluctuate until 120 kph on Idling.
3. Shifting Lever Can’t Shift to R When the Speed meter Fluctuate.

2) Study Guide Cause

• Due to poor contact from ECU socket terminal.

3) Study Guide And Diagnosis

• Scan Tool Check
  = U0101-TCM Communication Error,This trouble code appeared due to poor contact of terminal wire.(Note: You can search here the code to know the cause)
• Check the terminal wire and cean.

CONTINUE READING

Auto Repair and Study Guide and Auto Repair and Study Guide and Auto Repair

How to Repair Battery Indicator Lights On Code U1112

How to Repair Battery Indicator Lights On Code U1112.

 

2010  G 3.8 DOHC  Engine  Unleaded EOBD  U1112 LIN Communication Error

Auto Repair and Study Guide w/ Component Location Study Guide and General Description Many control units have applied to vehicle as it becomes more eletrolnical. These units control their own system based on information from diverse sensors. Therefore necessity of common use of diverse sensor information and importance of stable power supply are gathering strength. Battery sensor is mounted on battery (-) terminal. It transmits battery voltage, current, temperature information to ECM. ECM controls generating voltage by duty cycle based on these signals. Auto Repair w/ DTC Description ECM sets this code when there is an error in LIN communication line. DTC Detecting Condition Item Detecting Condition Possible cause DTC Strategy • Signal Monitoring     =Open or short in LIN communication line =UCU or ECM EnableConditions • Engine Run Time  2sec. • Ignition Voltage  11V Threshold value • LIN communication error Diagnosis Time • Continuous MIL On Condition • NO MIL ON(DTC only)

More case and Repair Study

How to Repair Engine Start But Suddenly Cut Off on idling Hyundai Sonata(YF)?

How to Repair Engine Start But Suddenly Cut Off on Idling Hyundai Sonata(YF)?

Model: Hyundai Sonata YF

Year Model: 2011

Fuel : Gasoline

Displacement: 2400cc

1) Study Guide For Condition

1. Engine Start but Suddenly Cut Off on Idling.
2. Engine Hesitate During Acceleration.

2) Auto Repair and Cause

1. Due to the OCV clogging with metal.

3) Study Guide and Diagnosis

1. Scan Tool Check = Trouble Code  P0011  Camshaft Position-Timing Over-Advanced or System Performance (Bank 1)
2. Check if what are the possible causes of this problem.
   

   • Oil leak

   more info:

More cases and Advice if you have some problem you can email me @ HERE 

 

 

 

How to repair engine jerking during driving

How to repair engine jerking during driving.

Auto repair and Study guide Give’s you some Guidelines or tips that problem occurs from Hyundai cars hoping that this post help you.

Model: Hyundai Elantra(HD)

Year Model: 2010

Fuel :Gasoline

Displacement: 1600cc

1) Condition

• Engine jerking during driving specially in high speed.
• Engine suddenly loose power after jerking.

2) Study Guide

• Due to the Ignition coil Extension wire.

3) Diagnosis

• Scan tool check
  = No trouble code
• Analyze the engine performance visually
• Check for terminal wire loose
• Ignition coil #1 socket terminal pin poor contact.

4) Auto Repair

• Check and Repair terminal.

Engine Electrical System
 

ON-VEHICLE INSPECTION

SPARK TEST

1.Remove the engine cover(A).

2.Remove the engine cover bracket(A) and the ignition coil(B).

3.Remove the fuel pump relay(A) from the fuse box for fuel not to be injected while checking.

4.Using a spark plug socket, remove the spark plug.

5.Install the spark plug to the ignition coil. (1.6 CVVT)

6.Ground the spark plug to the engine.

7.Check if spark occurs while engine is being cranked.

Do not crank engine for more then 5~10 seonds.

8.Inspect all the spark plugs.

9.Using a spark plug socket, install the spark plug.

10.Install the ignition coil.

 

11.Install the engine cocer.

 

INSPECT SPARK PLUG

1.Study Guide Remove the engine cover bracket(A) and the ignition coil(B) with bolt.

 

AUTO REPAIR INSPECT IGNITION COIL

1.Measure the primary coil resistance between terminals (+) and (-).

 

More Tips and Case Study

How to Check Engine is Not Turned “OFF” in Hyundai Santa Fe

How to Check Engine is not turned “OFF” in Hyundai Santa Fe.

 

This Auto Repair and Study Guide give you some basic trouble of Engine and Electrical

Model: Santa Fe(SM)

Year Model": 2001

Displacement: 200cc

Fuel: Diesel

Study Guide : Engine is not turned “OFF”

1) Study Guide COndition

1. When the ignition key is turned off the engine does not stop.
2. Fuel consumption is High.

2) Auto Repair and Cause

1. Scan tool check
   = No Trouble Code
2. Inspect the injector using injector quantity comparison mode in GDS
   = Low injector quantity comparison value of #2 cylinder.
3. Inspect after removing the injector.
   =The injector hole has been expanded.
   =After replacing the injectors, the engine”

4) Auto Repair

• Replace the injector assembly

More Info and reading

How to repair the rear A/C not working of Hyundai Trajet

How to repair the rear a/c not working of Hyundai Trajet

Auto repair and Study guide for you to have tips if your Hyundai Trajet occurs problem from a/c system.

1) Condition

• Rear Air condition system not working

2) Cause

• This was occurs problem from engine compartment junction box A/C fuse burnt pin.

3) Diagnosis

• Scan tool check
  = No trouble found
• Seems were a Technician of Hyundai cars we will first check up visually Scan tool and Fuses.
• Open and check for the fuse
  = Ok the fuse and the pin burn to the internal parts.

4) Auto Repair and Study guide

• Replace passanger Fuse box assembly.

 

2006  G 2.0 DOHC  Relay Box (Engine Compartment)

FUSIBLE LINK Study Guide SPECIFICATIONS Circuit Rated Capacity Circuit Rated Capacity Ignition switch 1 30A ABS 1 30A Ignition switch 2 50A ABS 2 30A Power window 30A Radiator 30A Condenser 20A     Auto Repair and Study Guide INSPECTION 1. 2. .   Caution . Study Guide and Study Guide Trouble and Study

How to check Code C1202 Wheel Speed Sensor Front-LH Invalid/no Signal

How to check code c1202 wheel speed sensor front LH invalid/no signal

This Auto repair and Study guide was trouble encounter from Hyundai Genesis regarding on ECS/ABS light indicator on some times while driving. this was the trouble code appeared from the GDS C1202 Wheel speed sensor but some of trouble can not immediately caught base on the trouble code given by the GDS this is only the basis so that every technician has pattern.

Auto repair and Study guide This trouble was solve and the cause was only from the tire. all tire defective oblong that’s why the sensor from wheel can not give good signal.

Component Location,Auto repair and Study guide

 

Study guide General Description

Study guide The ESP system is the shorten word of Electronic Stability Program system. This system recognizes a critical driving condition by Yaw-rate sensor, Lateral acceleration sensor and Steering angle sensor. And then it stabilizes the Study guide and vehicle by a individual wheel braking and engine torque control through CAN communication. Among components of this system, the wheel speed sensor(WSS) is the essential component of the brake system. Study guide The ESP ECU(HECU, Hydraulic and Electronic Control Unit) uses the wheel speed sensor's signals to calculate a vehicle speed and also this Auto repair to determine whether a wheel lock occurs or not.

Auto repair DTC Description

Study guide of The HECU monitors the wheel speed sensor signal continuously and if the signal of a wheel speed sensor is omitted or too low, this DTC is set.

DTC Detecting Condition and Auto repair.

Item
Detecting Condition
Possible Cause

• Signal Monitoring

• Poor connection

• Improper installation of wheel speed sensor

• Abnormal Rotor and wheel bearing

• Faulty Wheel speed

 

continue here MORE INFORMATION AND TROUBLE SHOOTING

 

Study guide  and  Auto repair / Study guide and Auto repair / Study guide and Auto repair

How to Check ESP Code C1101 Battery Voltage High

How to Check ESP Code C1101 Battery Voltage High

Electronic Stability Program C1101 Battery Voltage High

Auto repair

Study guide

Study guide Component Location Auto repair and Study guide w/ General Description Study guide for the ESP system is the shorten word of Electronic Stability Program system. Study guide This system recognizes a critical driving condition by Yaw-rate sensor, Lateral acceleration sensor and Steering angle sensor. And then it stabilizes the vehicle by a individual wheel braking and engine torque control through CAN communication. Study guide The ESP ECU(HECU, Hydraulic and Electronic Control Unit) checks the battery voltage and alternator output voltage to determine, as a safety issue, whether this system can operate normally or not.Study guide The normal battery voltage range is essential for controlling this system as intended.   Study guide DTC Description The HECU monitors the voltage of battery and if it stays more than 17 Volts, this DTC is set. DTC Detecting Condition Item and Study guide Auto repair w/ Detecting Condition Possible Cause or Study guide DTC Strategy and Study guide • Monitoring the voltage of battery • Poor connection in power supply circuit • Faulty Alterator • Faulty HECU Threshold valve and Study guide • When Battery voltage is more than 17V Fail-Safe and Study guide • ABS/EBD/TCS/ESP funtions are inhibited. • ABS/EBD/ESP warning lamps are activated. To continue more guide and Study Auto repair , Study guide , Auto repair , Study guide , Auto repair , Study guide , Auto repair